Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for League City Homeowners
A sagging gate in League City usually comes down to one thing: a part that wore out faster than the rest of the gate. The hinge, the roller, the post, or the latch failed, and now the whole gate drags, sticks, or won’t close at all. We replace those parts and weld what’s broken. Vance Gate Repair has repaired and installed over 22,000 gates since 2014, and every job starts with a written price before any work begins. If your gate is dragging on the concrete or the post is leaning after the last storm, call (346) 787-1751 and we’ll schedule a technician to come out, find the failed part, and show you exactly what it costs to fix.
What Our Gate Parts & Welding Service Includes
The work falls into six categories. Each one starts the same way: we look at the gate, identify what failed, and write down the repair scope and price before we touch a tool. Here’s what each job involves.
Hinge Replacement
A hinge is the pivot point that carries the entire weight of the gate leaf. When a hinge wears, the gate drops at the latch side and you’ll see a scrape mark on the concrete or a gap that widens at the top. We remove the old hinge, check the post for wallowed-out bolt holes, weld or sleeve the post if it’s damaged, and install a new hinge rated for the gate’s weight. Most hinge replacements on a residential driveway gate in League City run one to three hours depending on whether the post needs repair.
Post Replacement
The post is what everything hangs on. When a post rusts at ground level, gets hit by a car, or simply leans after years of wind load from the gate, the gate will never hang right until the post is reset. We saw off the old post at grade, break out the old concrete footing, set a new steel post in fresh concrete, and let it cure before re-hanging the gate. For posts damaged by rust, we specify and install galvanized or powder-coated posts that hold up against League City humidity.
Rail Repair
On a cantilever or rolling gate, the rail carries the gate across the driveway. A bent rail makes the gate bind and jump; a rusted rail section will eventually fail under load. We straighten bent rails where possible, cut out and weld in new rail sections where the damage is too far gone, and re-level the whole run so the gate travels smoothly. If the rail is out of level by more than a few degrees, we shim or re-pour the rail supports before welding anything, because welding a rail to a bad support doesn’t fix the problem.
Custom Welding
Some gates need a part that no catalog carries. A decorative scroll cracked loose, a picket broke off at the weld, an operator bracket tore away from the frame. We fabricate and weld replacement sections on site when the gate is repairable, and we photograph every weld before and after. Our technicians weld MIG and stick depending on the material and position, and we match the repair to the existing gate’s metal, whether it’s tubular steel, ornamental iron, or aluminum.
Gate Rollers
Sliding gates ride on rollers, and rollers wear out. When a roller bearing seizes or the wheel flattens, the gate gets louder and harder to move, and the motor works harder to compensate. We replace worn rollers, swap seized bearings, and re-set the gate height so the leaf rides level across the full travel. We also check the roller track for wear grooves and tell you if the track itself needs replacement before it chews through the next set of rollers.
Latch & Lock
The latch is the part you touch every day, so it fails more often than anything else on a gate. A latch that won’t catch means the gate won’t stay closed; a lock that’s seized means the gate won’t open when you need it to. We repair striker alignment, replace worn latch springs, free corroded lock cylinders, and install new latches and locks cut to match the existing gate frame. When the latch post is what’s moved, we address that first, because a new latch on a leaning post is a two-week repair at best.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
We work on gates fitted with motors and hardware from nine major automation brands, which matters when the part you need is specific to the operator. For LiftMaster and Elite operators, we keep common replacement components stocked in our League City service vehicles: limit switches, control boards, receiver modules, and hinge-side operator brackets. We’ve serviced hundreds of Mighty Mule units on residential gates and are familiar with their mounting patterns and the stress points where those brackets tend to crack. FAAC and BFT operators show up on a lot of the heavier commercial-style gates in the area, and we know the hinge and rail hardware those units put the most force through.
When a bracket tears off a LiftMaster arm, the repair is usually welding, and we do that on site. When a Mighty Mule mounting plate bends, we straighten or replace it and then check the hinge alignment that caused the extra load in the first place. Whether you have one of these brands or any other make, the approach is the same: find the part that failed, confirm the repair scope in writing, and fix it rather than steering you toward a replacement that you don’t need.
BeforeAfterSigns You Need Gate Parts & Welding Right Now
- The gate scrapes the driveway on the latch side. This means a hinge or a post has settled, and every cycle is grinding metal against concrete. The longer it runs like this, the more the frame twists and the more expensive the repair gets.
- The gate stops halfway and reverses. A bent rail or a seized roller forces the motor past its torque limit, which trips the operator into reverse. The motor is protecting the gate from a mechanical problem that hasn’t been fixed yet.
- The latch won’t seat without you lifting the gate. That lift is compensating for a dropped hinge or a leaning post. We see this on League City gates that have been through a few years of coastal wind, especially on properties with clay-heavy soil that shifts with rainfall.
- You hear a grinding or squealing when the gate moves. That’s a roller bearing or hinge pin that has lost lubrication or started to fail. Ignoring the noise means replacing the roller, the hinge, and possibly the mating surface instead of just one part.
- A weld has cracked visibly anywhere on the gate or post. A cracked weld is a structural failure in progress. The gate is carrying load through a joint that isn’t holding, and continued use spreads the crack through the surrounding metal.
None of these are cosmetic. Each one means a part is doing more work than it was designed for, and that always ends in a bigger repair bill than the one you could schedule today.
Our Gate Parts & Welding Process - Step by Step
- 1
We inspect and measure. The technician walks the gate, checks each hinge, roller, post, rail, and latch, and measures the gaps, levels, and clearances. We photograph what we find, and we write down the findings in plain language.
- 2
You get a written price. Before any work starts, you receive a written scope of work and a flat price. This is Haven Standard Clause 1: have it in writing. You approve the number, and only then do we pick up a tool.
- 3
We do the repair. The technician removes the failed part, preps the mounting surface or weld joint, and installs the replacement or completes the weld. We use the right fastener grade and the right welding process for the material and position, and we torque or weld to spec.
- 4
We test the gate under load. The gate cycles open and close several times after the repair. We check travel limits, listen for noise, and confirm the latch seats without manual lifting. For automated gates, we verify the operator’s force settings are not fighting the repaired mechanical parts.
- 5
You get the photo record. Under Haven Standard Clause 4 (Evidence on every job), every visit includes a documented photo record: what was found, what was adjusted, what was replaced, and how it looked at the end. The photos are yours to keep and filed in the job record so any future technician can see exactly what was done.
How Much Does Gate Parts & Welding Cost in League City?
If you’re wondering how much Gate Parts & Welding costs, pricing in League City breaks down by the part and the labor to install it. A hinge replacement on a standard residential swing gate typically runs $180 to $420 per hinge depending on the gate’s weight and whether the post needs repair. A single post replacement, including concrete work, lands between $450 and $900. Rail repairs run $200 to $600 depending on how much rail needs straightening or sectioning. Custom welding jobs start around $150 for a simple crack repair and go up based on fabrication time and material. Roller replacements run $120 to $300 per roller including the bearing. A latch and lock repair usually falls between $150 and $350.
What moves the price: gate weight, post condition, access to the work area, and whether the gate is automated (operator settings have to be rechecked after any mechanical repair). What doesn’t move the price: guesswork. You’ll see the number in writing before we start, and it won’t change at the end unless you approve additional work in advance. The home page lays out the full Haven Standard if you want to understand exactly how we quote. For a free estimate on your specific gate, call (346) 787-1751 and we’ll send a technician out to measure and write it up.
Gate Parts & Welding Near League City - Our Service Area
We run gate parts and welding calls throughout League City and into the surrounding communities. If you’re in Webster, Friendswood, Dickinson, Santa Fe, or La Marque, a technician can typically reach your property the same day you call. We also cover Bacliff, Alvin, Pasadena, La Porte, Pearland, and Texas City. For neighbors just over the line, check our Gate Parts & Welding in Webster page or the Gate Parts & Welding in Dickinson page for town-specific detail. A live person answers the phone at any hour, so you’ll never hit a voicemail loop when you call (346) 787-1751.
Serving League City, TX - Our Local Coverage Area
We’re based in the League City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in League City
Our Gate Parts & Welding in Webster covers the repair and replacement of the structural and mechanical components that a gate hangs, rides, latches, and pivots on. That includes hinges, posts, rails, rollers, latches, locks, and custom fabricated brackets or sections. When a part fails, we replace it or weld it back into the gate structure, then test the gate under load to confirm the repair holds. Call (346) 787-1751 if you’re not sure whether your gate needs a new part or a weld; we’ll tell you in writing before we do anything.
Most hinge, roller, and latch repairs take one to three hours on site. A post replacement takes longer because the concrete around the new post has to cure before the gate can be re-hung, usually 24 to 48 hours. Custom welding jobs vary based on how much fabrication is required, but simple crack repairs are often done in under two hours. We’ll give you a time estimate with the written price before we start.
Depending on the part and the labor involved, expect $150 to $900 for most residential our Gate Parts & Welding in Dickinson repairs. Hinge replacements and latch repairs sit at the lower end; post replacement and significant custom welding sit at the higher end. The price depends on the gate’s weight, the condition of the surrounding structure, and whether the gate runs on an automated operator that needs rechecking after the mechanical work. For a firm number on your gate, call (346) 787-1751 and we’ll provide a free written estimate.
Yes. We service LiftMaster gates regularly, and for the welded brackets and hinges on LiftMaster-equipped gates, we handle the fabrication and repair on site. We also work on Elite, Mighty Mule, FAAC, and most other automation brands you might find already installed on a League City gate. You don’t need to have a specific brand of motor for us to repair the gate itself; the mechanical and structural work is independent of the operator. Call (346) 787-1751 to describe what’s failing and we’ll give you a straight answer.
Yes. We keep same-day availability for gate failures that leave a property unsecured or a gate stuck across the driveway. A live person answers the phone 24 hours a day, seven days a week, and we dispatch a technician to League City addresses the same day in nearly every case. If your gate is stuck open, stuck closed, or the post has failed and the gate is hanging off its hinges, call (346) 787-1751 now and we’ll get someone on the way.
Every repair we complete is covered by our 365-Day Done Right Promise: if the repair is not right, we make it right within that year at no additional charge. The parts we install carry their manufacturer warranty, and our welding and labor are covered for a full year. No argument, no fee, no expiration date within that window. If something doesn’t hold, call us and we’ll send a technician back to make it right.
Clear the area around the gate on both sides if you can, and make sure the gate’s power switch is accessible if the gate is automated. You don’t need to remove anything or have tools ready; the technician brings everything. If you have paperwork from a previous gate repair or a written estimate from another company, set it aside, because we offer a free second opinion on any written estimate from another company. A human will call or text before arrival with the technician’s name and photo.
Schedule Your Gate Parts & Welding Service in League City Today
If you’re reading this because a gate is dragging, leaning, or won’t latch, that’s a repair that only gets more expensive the longer it waits. Call (346) 787-1751 and a live person will answer, take the details, and schedule a technician to come out to your League City property. You’ll get a written price before any work begins, a documented photo record when the job is done, and a full year of coverage under the 365-Day Done Right Promise. Free estimates, no obligation, and no surprise invoice at the end.
Written by Adrian Vance, Owner at Vance Gate Repair, serving League City since 2014.