Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Texas City, TX
Gate access control in Texas City means securing properties that sit a few feet above sea level in salt air, where control boards corrode and keypads fog from the inside. Most Texas City homes we visit were built between the 1950s and 1970s on slab foundations, and their gate wiring was never intended for forty years of Gulf humidity and the occasional storm surge. We diagnose the actual condition of the access system, write the price down, and leave you a photo record of every reading and replacement. Call (346) 787-1751 if a gate has stopped responding to its keypad, remote, or intercom.
Why Texas City Homes Are Different
Texas City’s industrial corridor along Galveston Bay shapes the gate work here in a way that doesn’t exist fifteen miles inland. The refinery and port perimeter gates run high-cycle operators all day, every day, and that demand has made industrial-grade access control and heavy slide-gate repair a core skill set for technicians who work this city. We keep sealed enclosures and corrosion-rated hardware on the truck because we know what the salt air does to exposed metal.
Residential properties are different from the industrial sites but they share the same atmosphere. Homes near the Texas City Dike and bayside streets see uncoated iron hinges and operator housings rust through within two to three years. Housing stock from the post-1947 rebuild and mid-century expansion sits low and flat, so underground conduit for gate wiring floods in heavy rain and dries out poorly. We routinely find control boards that shorted during a storm because water wicked up through conduit that was never sealed at the pedestal. That’s a Texas City pattern, and it changes what parts we stock and which enclosures we install.
Our Main Texas City Services
These are the three services Texas City homeowners and property managers call us about most often, each linked to its own detailed page.
Gate Repair in Texas City
A gate that won’t open, grinds against its track, or sags onto the latch is a different problem in Texas City than in a dry inland suburb. Salt corrosion seizes hinges faster, and flood events leave silt inside operator housings that most repair companies never open. We document what we find, replace what’s failed, and reset the travel limits so the gate closes fully without slamming. See the full scope of repair work in this city on our Gate Repair in Texas City page.
Gate Installation in Texas City
New gate work in Texas City has to account for wind load off the bay, soil that stays wet, and hardware selection that can hold up to salt air. We quote the gate, the posts, the operator, and the conduit work in writing before anything is ordered, and we photograph the pad pour and the post set so the record is there if you ever need it. See Gate Installation in Texas City for details on what a full install includes.
Gate Motor & Opener in Texas City
Automatic openers near the bay fail from corrosion and water intrusion more than from wear. We service nine major brands so the fix usually means replacing the board, the capacitor, or the limit switch rather than the whole operator. When we set a motor, we record the limit-switch positions and torque readings so the next service call starts from data, not guesswork. Read more on our Gate Motor & Opener in Texas City page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Texas City
Gate access control is the layer between the street and the driveway: keypads, remotes, card readers, phone entry, and video intercoms. In Texas City, the salt air and recurring flood events mean these systems fail in predictable ways. Keypads corrode at the ribbon connector, photo-eyes crack from UV exposure, and control boards short when conduit fills with water after a hard rain. Our Gate Access Control service covers repair and replacement of all of it, and every visit ends with a written record of what was found and what was installed.
Keypad Entry
Signs you need it
The keypad accepts the code but the gate doesn’t move, or the buttons stick and register wrong digits.
What it costs in Texas City
Replacing a gate keypad in Texas City typically runs $140 to $540 depending on whether it’s a standalone unit or tied into an existing operator’s control board.
How we do it
We test the keypad circuit, check the wiring at the operator for corrosion, install the new unit with sealed connectors, and program the codes in front of you.
Phone Entry
Signs you need it
Callers can’t hear the dial tone, the gate won’t release from the phone, or the unit’s display shows an error after rain.
What it costs in Texas City
Phone entry system repair in Texas City usually runs $85 to $450 depending on whether the fault is in the handset, the relay, or the main board.
How we do it
We trace the signal from the phone unit to the operator relay, replace the failed component, and test the release sequence three times before we leave.
What Gate Access Control Costs in Texas City
| Item | Typical range in Texas City |
|---|---|
| Keypad replacement | $140-$540 |
| Phone entry repair | $85-$450 |
| Control board replacement | $200-$800 |
Does a gate access system need permits in Texas City?
Low-voltage access control work typically doesn’t require a permit in Texas City. If the job involves new line-voltage electrical, we’ll tell you before work starts and coordinate the permit if one is required.
Can you replace only the keypad, or do I need a whole new system?
In most cases we replace just the failed component. A corroded keypad doesn’t require a new operator. We’ll show you what failed before we quote the replacement part.
Gate Parts & Welding in Texas City
Salt air on Galveston Bay shortens the life of every steel component on a gate. Hinge barrels rust through, posts rot at the base, and rails warp under years of wet soil movement. Our Gate Parts & Welding service repairs the structural steel so you don’t pay for a full gate replacement when one post or one hinge was the problem.
Hinge Replacement
Signs you need it
The gate sags toward the latch side, the hinge barrel is flaking rust, or the gate scrapes the ground on the swing arc.
What it costs in Texas City
Hinge replacement in Texas City generally runs $150 to $600 per hinge depending on gate weight and whether the post needs reinforcement.
How we do it
We support the gate, cut the old hinge, inspect the post for internal rust, weld the new hinge at the correct offset, and photograph the final weld.
Post Replacement
Signs you need it
The post leans, the concrete base is cracked, or the post moves when the gate opens and closes.
What it costs in Texas City
Post replacement in Texas City typically costs $900 to $2,700 including excavation, new steel, concrete, and re-hanging the gate.
How we do it
We remove the old post, inspect the soil and old concrete, set the new post with drainage at the base, and align the gate before it’s welded into place.
What Gate Parts & Welding Costs in Texas City
| Item | Typical range in Texas City |
|---|---|
| Hinge replacement | $150-$600 |
| Post replacement | $900-$2,700 |
| Rail repair | $150-$900 |
Can you weld a cracked gate on site in Texas City?
Yes. We carry a mobile welder and can repair most cracks in the gate frame, rail, or hinge point on site in Texas City the same trip. The repair is photographed and documented before we leave.
How long does post replacement take?
Most post replacements take five to eight hours including concrete work. The gate stays supported during the job, and you’ll have a written record of the depth, new post gauge, and concrete used.
Brands We Service in Texas City
We service BFT, Linear, Viking, Ghost Controls, and five other major gate-automation brands. Common boards, remotes, and photo-eyes for these brands are stocked on our service trucks, which keeps most Texas City repairs to a single visit. See our brands page for the full list.
Pricing for Gate Repair in Texas City, TX
| Service | Typical range in Texas City |
|---|---|
| Keypad replacement | $140-$540 |
| Phone entry repair | $85-$450 |
| Control board replacement | $200-$800 |
| Hinge replacement | $150-$600 |
| Post replacement | $900-$2,700 |
| Rail repair | $150-$900 |
| Gate roller replacement | $120-$900 |
| Custom welding (per hour) | $95-$190 |
Prices push higher in Texas City when a gate needs corrosion repair before new parts can mount, or when storm flooding has damaged multiple components at once. Every quote is written down and agreed before any work starts; if the invoice ever exceeds the written price without your approval, you don’t pay the difference. That’s the rule, not a courtesy.
Neighborhoods We Serve in Texas City
We work across the city, from bayside streets along the Dike to neighborhoods near 34th Street and the older grid around 6th Street. Response time averages same-day for gate emergencies when a gate is stuck open or won’t close at all.
- Bay Street Park
- Texas City Dike area
- Old Town / 6th Street
- Hughes Manor
- West Side near the levee
Service Area - Cities Near Texas City
Our Texas City crews also serve the surrounding communities along the bay and inland. If you’re in La Marque, TX, Dickinson, TX, Bacliff, TX, or Santa Fe, TX, the same team can schedule your gate work with the same written pricing policy.
Serving Texas City, TX - Our Local Coverage Area
We’re based in the Texas City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Texas City
A stuck-open gate in Texas City gets same-day dispatch. Crews are scheduled from the Houston office and serve Texas City locally, so response time is usually measured in hours, not days. Call (346) 787-1751 and a person answers.
Yes. High-cycle slide gates, security checkpoint barriers, and OSHA-compliant access control are part of our regular work in this city. The same documentation and written pricing apply to commercial gates as to residential.
Call us before you try to run the operator. Water, silt, and salt intrusion is exactly what we find on Texas City callouts, and the fix usually starts with opening the enclosure and documenting what reached the board. Don’t attempt repairs yourself.
If you’re ready for a written price on gate access control or structural repair in Texas City, call (346) 787-1751. Estimates are free, the price is on paper before any tool comes out, and a live person answers around the clock.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Texas City Customers Say
"Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.