Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Pasadena, TX
Gate access control in Pasadena means keypads, card readers, phone-entry systems, and video intercoms on gates that endure some of the most corrosive air along the Houston Ship Channel. Older post-WWII homes near industrial corridors keep perimeter fencing and driveway gates at a higher rate than neighboring suburbs, and pre-Harvey electrical systems that were patched quickly after 2017 flooding fail every rainy season. We quote every access-control job in writing before work starts, and a live person answers at (346) 787-1751 any hour you call.
Why Pasadena Homes Are Different
Pasadena sits directly in the petrochemical corridor, and the ambient sulfur compounds, hydrogen sulfide, and industrial off-gases from surrounding refineries accelerate oxidation on iron and steel at a rate far beyond what Pearland or League City see. A gate that holds up 15 years in a typical Houston suburb may rust, pit, and seize in 7 to 10 years here. That one condition changes every material decision we make.
The housing stock compounds it. Residential streets built during the 1950s-1970s petrochemical boom hold thousands of original chain-link and tubular steel ornamental gates that were installed during that era and never replaced. Flood history matters too: Hurricane Harvey put entire blocks underwater, and gates set in saturated soil heave and lean. Operators submerged even briefly during heavy rain frequently need motor and circuit board replacement. East of Shaver Street and around Strawberry Road, we routinely find corroded control boards and improperly waterproofed conduit runs that were repaired with budget parts after 2017 and now fail on a seasonal schedule.
Our Main Pasadena Services
Pasadena homeowners call us most often for three core services beyond access control and parts work. Each gets a dedicated page with full pricing.
Gate Repair in Pasadena
Won’t open, grinding, sagging, off-track, post leaning after a flood event. Gate repair in Pasadena covers swing and slide gates, broken hinges, seized rollers, bent rails, and operator resets. The industrial air here means we check for corrosion even when the visible problem looks mechanical. Every repair gets a written price before we touch anything. Full details: Gate Repair in Pasadena.
Gate Installation in Pasadena
New construction, replacement of a rusted 1960s chain-link gate, or a full driveway gate with automation. Pasadena soil after Harvey means post depth and concrete footing matter more than in drier suburbs. We use corrosion-resistant hardware as standard here. Measured, ordered, scheduled, and priced in writing. Full details: Gate Installation in Pasadena.
Gate Motor & Opener in Pasadena
Operator dead after a storm, motor grinding, remote stopped working, gate reverses mid-cycle. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Pre-Harvey electrical systems fail predictably in flood-affected blocks, and we photograph every limit-switch setting we change. Full details: Gate Motor & Opener in Pasadena.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Pasadena
In Pasadena, access control work usually means updating an older home’s keypad or adding a phone-entry system to a driveway gate that still runs on a 1990s control board. The combination of industrial air corrosion and post-Harvey electrical patching means we’re often replacing corroded wiring terminals and water-damaged boards rather than just swapping a keypad. This is the core of our Gate Access Control practice: the gate itself may be fine, but the system that tells it to open is not.
Keypad Entry
Signs you need it
Dead keys, intermittent codes, or a keypad that works after rain but not during humidity swings.
What it costs in Pasadena
Replacement keypads typically run $185 to $380 installed, closer to the high end when we have to replace corroded terminal blocks.
How we do it
We test the existing wiring, replace the keypad and any corroded terminals, program your codes, and photograph the finished connections.
Phone Entry
Signs you need it
Delivery drivers can’t reach you, or you want guest access without handing out codes that never change.
What it costs in Pasadena
Phone-entry systems run $450 to $900 installed, depending on whether we’re adding a cellular unit or integrating with an existing intercom line.
How we do it
We mount the unit, connect it to your gate operator’s control board, configure call routing to your phone, and document every setting.
What Gate Access Control Costs in Pasadena
| Item | Typical range in Pasadena |
|---|---|
| Keypad replacement | $185 - $380 installed |
| Phone entry system | $450 - $900 installed |
| Control board replacement | $250 - $600 installed |
Can you fix a keypad that stopped working after a Pasadena storm?
Yes. We trace the circuit from the keypad to the operator, replace anything corroded or water-damaged, and reset the code memory. Most storm-damaged keypads are fixed same-day. Call (346) 787-1751 and we’ll confirm.
Will a phone-entry system work with my older Pasadena gate operator?
In most cases, yes. We match the phone-entry relay output to your operator’s control board input, even on 1990s-era boards. If the board is too far gone, we’ll show you the corrosion and quote a replacement before proceeding.
Gate Parts & Welding in Pasadena
Pasadena’s industrial air pits steel fast and weld joints fail earlier here than almost anywhere else in the metro. The older chain-link and tubular steel gates from the 1950s-1970s boom years often outlive their hinges, posts, and weld points, which means parts replacement and welding form a large share of our Gate Parts & Welding work. On flood-affected blocks, posts that leaned after Harvey stay leaned until someone digs them out and sets them deeper.
Hinge Replacement
Signs you need it
The gate drags on the latch side, squeals when opening, or shows rust streaking below each hinge.
What it costs in Pasadena
Hinge replacement runs $90 to $220 per hinge, including grinding off the old one and welding the new in place.
How we do it
We cut or grind the old hinge, weld the replacement, check gate swing alignment, and photograph the finished weld.
Post Replacement
Signs you need it
The post leans, the gate sags, or concrete around the base has cracked and pulled away from the steel.
What it costs in Pasadena
Post replacement runs $280 to $600 per post, depending on depth and whether the old footing must be broken out.
How we do it
We dig out the old post and footing, set a new post in concrete below the water table, brace it level, and rehang the gate.
What Gate Parts & Welding Costs in Pasadena
| Item | Typical range in Pasadena |
|---|---|
| Hinge replacement | $90 - $220 per hinge |
| Post replacement | $280 - $600 per post |
| Rail or frame welding repair | $120 - $350 per repair |
Can you weld a rusted gate frame back together?
Often yes, if the surrounding steel is still sound. We grind back to clean metal, assess the remaining wall thickness, and weld only if it will hold. If the frame is too thin, we’ll tell you and quote replacement. Call (346) 787-1751 for an honest assessment.
Why do Pasadena gate posts lean after heavy rain?
Saturated soil lets posts shift, especially where Harvey floodwater softened the original 1960s footings. Resetting the post deeper, often below the local water table, usually stops the cycle. We quote the depth and concrete volume in writing before digging.
Brands We Service in Pasadena
We work on LiftMaster, FAAC, and Elite automation with parts stocked locally in the Houston area, plus Mighty Mule and five other major brands. If your operator is older and the exact board is discontinued, we source compatible replacements and document what went in. See our brands for the full list.
Pricing for Gate Repair in Pasadena, TX
| Service | Typical range in Pasadena |
|---|---|
| Keypad replacement | $185 - $380 installed |
| Phone entry system | $450 - $900 installed |
| Control board replacement | $250 - $600 installed |
| Hinge replacement | $90 - $220 per hinge |
| Post replacement | $280 - $600 per post |
| Rail or frame welding repair | $120 - $350 per repair |
Corrosion from industrial air pushes Pasadena prices toward the upper end of these ranges more often than in Pearland or Deer Park, simply because we’re replacing more corroded terminals, fasteners, and weld-prep surfaces. Every price is written and handed over before any work starts, and it doesn’t change at the end of the job.
Neighborhoods We Serve in Pasadena
We run calls across Pasadena’s older residential blocks, from the streets east of Shaver to the neighborhoods around Strawberry Road and across the flood-affected zones that trace Harvey’s path. Our Houston dispatch office coordinates crews locally, so response time from the metro office is typically under an hour for emergency gate work.
- East of Shaver Street
- Strawberry Road corridor
- Red Bluff Terrace
- Southmore area
- Vista Villas
Service Area - Cities Near Pasadena
We also cover the neighboring industrial and shoreline communities where gate corrosion and flood history create the same failure patterns. That includes Deer Park, TX, Channelview, TX, La Porte, TX, and Pearland, TX, all served from the same Houston dispatch office with local crews.
Serving Pasadena, TX - Our Local Coverage Area
We’re based in the Pasadena area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Pasadena
A live person answers at (346) 787-1751 any hour, and we dispatch crews from the Houston metro office into Pasadena typically within an hour for emergency work. Gate down across a driveway or a stuck-open gate gets triage on the call so we know what parts to bring.
Most residential gate repairs and part replacements don’t require a permit. New installations with concrete footings or electrical runs sometimes do, and we check the current Pasadena requirements before quoting. If a permit is needed, it’s included in the written scope.
For common repairs like keypad swaps, hinge weld jobs, and post resets, we can often give a firm price from photos and a short call. Larger access-control or welding projects get a measured on-site visit with a written price before you commit to anything.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Pasadena Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E.